| No. |
Part No. |
Description |
Qty |
Remarks |
| 1 |
FAM6257/9 |
Flywheel housing |
1 |
|
| 1 |
DAM6074 |
Flywheel housing |
1 |
Turbo only |
| 1 |
DAM6259 |
Flywheel housing use with DAM3745 |
1 |
998cc |
| 1 |
TRD10015 |
Flywheel housing use with AHU1707 |
1 |
1300cc |
| 2 |
AHU1707 |
Idler Bearing 1.375" O.D |
1 |
.875 ID |
| 2 |
DAM3745 |
Idler Bearing 1.375" O.D |
1 |
.750 ID |
| 2 |
13H7848 |
Idler Bearing 1.065" O.D |
1 |
4 sync, early |
| 2 |
88G302 |
Idler Bearing 1.004" O.D |
1 |
3 synchro |
| 3 |
AAU8424 |
1st motion shaft nose bearing |
1 |
was 13H6080 |
| 3 |
ADU6033 |
1st motion shaft nose bearing 1.692" O.D |
1 |
turbo only |
| 4 |
2A3643 |
Circlip for AAU8424 in flywheel housing |
1 |
|
| 4 |
ADU7194 |
Circlip for ADU6033 in flywheel housing |
1 |
turbo only |
| 5 |
CCN10 |
Circlip for holding 1st motion shaft bearing |
1 |
|
| 6 |
13H2934 |
Clutch oil seal (DAM2821 seal protector availaible |
1 |
|
| 6 |
LVF1005 |
Clutch oil seal (reluctor type flywheel) |
1 |
Injection only |
| 7 |
22A2237 |
Flywheel casing gasket, non genuine |
1 |
|
| 7 |
GUG7055563GM |
Flywheel casing gasket, genuine |
1 |
|
| 8 |
BH605141 |
Clutch case screw, long |
3 |
DAM7758 Alternative |
| 9 |
GHF332 |
Clutch case washer, was LWZ305 |
3 |
|
| 10 |
GHF103 |
Screw, Short was SH605081 |
3 |
DAM7753 Alternative |
| 11 |
22A1762 |
Locktab |
1 |
Part 18G8086 |
| 12 |
22A1761 |
Locktab |
1 |
Part 18G8086 |
| 13 |
2A3521 |
Locktab |
1 |
Part 18G8086 |
| 14 |
FNZ505 |
Nut |
9 |
|
| 15 |
GHF332 |
Washer, was LWZ305 |
4 |
|
| 16 |
22A1241 |
Locktab |
1 |
Part 18G8086 |
| 17 |
88G300 |
Cover with timing hole |
1 |
NLA |
| 17 |
AHU1106 |
Cover, verto with no timing hole |
1 |
|
| 18 |
DAM7755 |
Bolt, clutch cover |
8 |
|
| 19 |
2A3635 |
Cover to timing hole |
1 |
|
| 20 |
SH604041 |
Screw for timing cover hole |
2 |
|
| 21 |
GHF331 |
Washer |
2 |
|
| 22 |
22A180 |
Plunger,press fit for release bearing GRB238 |
1 |
|
| 22 |
DAM1955 |
Plunger which takes GRB238 & DAM2413 |
1 |
|
| 23 |
DAM2413 |
Clip to Hold GRB238 to DAM1955 |
1 |
Release bearing fits lose on plunger from 1982 on |
| 24 |
DAM5353 |
Plunger, verto clutch |
1 |
|
| 25 |
22A427 |
Plunger stop |
1 |
|
| 26 |
NT610041 |
Nut, was FNZ210 |
1 |
|
| 27 |
22A2204 |
Clutch arm, pre verto. Was 2A3518 |
1 |
|
| 28 |
DAM5355 |
Clutch arm, short, verto only |
1 |
1982 on |
| 29 |
CLZ628 |
Clevis pin, lever to case |
1 |
|
| 30 |
GHF302 |
Washer, was PWZ106 |
1 |
|
| 31 |
GHF101 |
Adjusting screw, was HZS409 |
1 |
|
| 32 |
FNZ604 |
Locking Nut |
1 |
|
| 33 |
CLZ518 |
Clevis pin, lever to push rod |
1 |
|
| 34 |
2A3601 |
Spring Anchor |
1 |
|
| 35 |
GHF301 |
Washer, was FWZ105 |
1 |
|
| 36 |
1G5999 |
Clutch spring |
1 |
|
| 37 |
2A3600 |
Anchor spring end |
1 |
pre verto |
| 38 |
13H396 |
Slave cylinder push rod |
1 |
All Minis |
| 38 |
PRS032 |
Adjustable stainless steel slave cylinder push rod |
1 |
All Minis |
