| No. |
Part No. |
Description |
Qty |
Remarks |
| 0 |
BEB-08 |
High-grade bolt kit |
1 |
|
| 1 |
12G123 |
Connecting rod number 2 and 4 |
2 |
|
| 1 |
12G126 |
Connecting rod number 1 and 3 |
2 |
|
| 2 |
2A660 |
Locktab |
4 |
|
| 3 |
12G2217 |
Big end bolt |
8 |
|
| 4 |
8G2733 |
Crankshaft (casting number 12A595) (12A1451) |
1 |
998cc and Cooper 998cc |
| 4 |
8G2732 |
Crankshaft (casting number 12G82) |
1 |
1100cc |
| 5 |
6K836 |
Crankshaft key |
1 |
|
| 6 |
VP572 |
Con rod bearings |
1 |
Also in 10/20/30/40 oversize |
| 7 |
VP733 |
Mains bearings |
1 |
Also in 10/20/30/40 oversize |
| 8 |
VPW81 |
Thrust washer set |
1 set |
Also in 03/30 thou oversize |
| 9 |
22A1493 |
Primary gear (24 teeth) |
1 |
|
| 10 |
DAM8887 |
Bush front was 22G401 |
1 |
|
| 11 |
22G109 |
Bush rear |
1 |
|
| 12 |
22A321 |
Thrust washers 2.79-2.84mm (.110-112") |
1 |
These shims are used to give the correct end float
of 3-6 thou on the primary gear check 22A319 and 88G459 for wear.
|
| 12 |
22A322 |
Thrust washers 2.84-2.89mm (.112-114") |
1 |
|
| 12 |
22A323 |
Thrust washers 2.89-2.94mm (.114-116") |
1 |
|
| 12 |
22A324 |
Thrust washers 2.94-2.99mm (.116-118") |
1 |
|
| 12 |
22A450 |
Thrust washers 2.99-3.04mm (.118-120") |
1 |
|
| 13 |
22A319 |
U Clip thrust |
1 |
|
| 14 |
88G549 |
Backing ring |
1 |
|
| 15 |
AEA630 |
Camshaft |
1 |
1100cc and 998cc Cooper |
| 15 |
8G712 |
Camshaft |
1 |
998cc |
| 16 |
2A299 |
Camshaft oil pump drive |
1 |
NLA (Fitted in camshaft new) |
| 17 |
WKN505 |
Camshaft key pin |
1 |
|
| 18 |
AHU2379 |
Camshaft plate |
1 |
|
| 19 |
GHF117 |
Locating plate bolt |
3 |
|
| 20 |
GHF321 |
Locating bolt shakeproof washer |
3 |
|
| 21 |
2A85 |
Camshaft gear with tensioners |
1 |
|
| 22 |
8G549 |
Tensioner rubber rings |
2 |
|
| 23 |
12G4337 |
Camshaft gear, used originally without tensioner |
1 |
|
| 24 |
12G2621 |
Tensioner, fits 12G2626 front plate only |
1 |
From engine number 99H791, 10H791 Not 998 Cooper |
| 25 |
12G2628 |
Tensioner mounting plate |
1 |
|
| 26 |
12G2629 |
Pivot pin |
1 |
|
| 27 |
6K629 |
Camshaft nut |
1 |
|
| 28 |
2A759 |
Camshaft locktab |
1 |
|
| 29 |
8G725 |
Crankshaft gear |
1 |
|
| 30 |
6K628 |
Washer to shim crank gear |
1 |
|
| 31 |
3H2127 |
Timing chain (Simplex) |
1 |
|
| 32 |
2A970 |
Front plate - pre tensioner type |
1 |
NLA |
| 32 |
12G2626 |
Front plate - used with tensioner pads |
1 |
|
| 33 |
12G619 |
Gasket for 2A970 front plate |
1 |
|
| 33 |
12G2981 |
Gasket for 12G2626 front plate |
1 |
|
| 34 |
12G4499 |
Distributor drive spindle |
1 |
|
| 35 |
13H2792 |
'O' ring distributor housing |
1 |
|
| 36 |
12A1136 |
Housing |
1 |
CWE |
| 37 |
2A14 |
Push rod |
8 |
|
| 38 |
2A13 |
Cam follower |
8 |
|
| 38 |
AEG584 |
Cam follower with oil hole |
8 |
High-grade |
