| No. |
Part No. |
Description |
Qty |
Remarks |
| 1 |
18G8065 |
Gearbox lock tab kit |
1 |
not shown |
| 2 |
GHF102 |
Gearbox case, front block to gearbox bolt |
5 |
1 also on 22H983 |
| 3 |
GHF102 |
Gearbox case, rear block to gearbox set screw |
4 |
1 also on front |
| 4 |
BH6044140 |
Bolt for dowel on front |
1 |
|
| 5 |
22H983 |
Case to block rear dowel |
1
|
|
6
|
FHS2409 |
Stud, rear stud for thin flange block |
2 |
|
| 6 |
FHS2410 |
Stud, rear stud for thick flange block |
2 |
|
| 7 |
2A3502 |
Gear change linkage bushing |
2 |
|
8
|
13H577 |
Gear change oil seal |
1 |
|
| 9 |
53K266 |
Stud for diff housing, long 4.5", 2 only for rod change |
4 |
NLA use TAM1617 |
| 10 |
53K1471 |
Stud for diff housing, short 3.5" x .250 thread |
3 |
Use CHS522 |
| 10 |
22G1834 |
Stud for diff housing, short 3" x .375 thread |
2 |
Rod Change only |
| 11 |
22A152 |
Long Stud for flywheel housing |
6 |
Alt DAM7759 |
| 12 |
53K547 |
Short stud for flywheel housing |
3 |
Alt DAm7756 |
| 13 |
53K1474 |
Stud for speed drive housing cover |
3 |
Alt DAM7761 |
| 14 |
22A153 |
Dowel for diff housing |
2 |
|
| 15 |
22A97 |
Dowel for flywheel housing |
2 |
|
| 16 |
22A13 |
Dowel for speed drive housing |
2 |
|
| 17 |
22A74 |
Diff housing lock tabs, Remote |
1 |
Part of 18G8085 |
| 17 |
42H500 |
Diff housing lock tabs, rod change |
1 |
" " |
| 18 |
22A251 |
Diff housing lock tabs |
1 |
" " |
| 19 |
2A3505 |
Upper gasket for diff housing |
1 |
|
| 20 |
2A3506 |
Lower gasket for diff housing |
1 |
|
| 20a |
22G1836 |
Lower gasket for diff housing |
1 |
Rod change |
| 21 |
AHU1672 |
Gearchange oil seal, rod change |
1 |
was 13H6862 |
| 22 |
88G302 |
Idler gear bearing with 1.004" or 25.5mm O/D |
1 |
3 Sync |
| 22 |
13H7848 |
Idler gear bearing with 1.065" or 27.05mm O/D |
1 |
4 Sync |
| 22 |
DAM3745 |
A+ idler gear bearing 1.375" or 34.92mm. 3/4" or 19mm ID |
1 |
|
| 22 |
TUK100320 |
A+ idler gear bearing 1.375" or 34.92mm. 5/8" or 22.25mm ID |
1 |
was AHU1707 |
| 23 |
22G1141 |
Clip for 3 Sync case where 88G302 is fitted |
|
NLA |
| 23 |
51K3565 |
Circlip for 4 sync where 13H7848 is fitted |
1 |
|
| 24 |
DAM5219 |
Speedo drive housing cover |
1 |
was 88G207 |
| 25 |
22A541B |
Gasket for housing, |
1 |
|
| 25 |
GUG7055569GM |
Gasket for housing, genuine |
1 |
|
| 26 |
2A3636 |
Speedo drive cast plate |
1 |
|
| 27 |
GUG705564GM |
Gasket for Speedo drive case plate |
1 |
was 2A3627 |
| 28 |
22A335 |
Oil strainer |
1 |
|
| 29 |
22A341 |
Suction pipe sealing ring |
1 |
|
| 30 |
22A388 |
Lock tab |
1 |
|
| 31 |
22A1365 |
Lock tab |
1 |
|
| 32 |
22A377 |
Oil suction pipe 850cc |
1 |
|
| 33 |
GUG705556GM |
Pipe to case flange gasket |
2 |
was 22A542b |
| 34 |
2K4874 |
Lock Tab |
1 |
|
| 35 |
2A3606 |
Oil suction searing ring - case to block |
1 |
|
| 36 |
DAM3755 |
Magnetic drain plug |
1 |
|
| 37 |
AED172 |
Washer for Drain plug |
1 |
|
| 38 |
GUG703038SG |
Gearbox to engine gasket |
1 |
|
| 39 |
AHU1959 |
Seal, half moon |
1 |
Was 12G2947 |
| 40 |
13H7286 |
Bushing for gear leave steady bar |
1 |
|
