| No. |
Part No. |
Description |
Qty |
Remarks |
| 1 |
21A1485 |
Hydrolastic radius arm R/H |
1 |
CWE |
| 1 |
21A1489 |
Hydrolastic radius arm L/H |
1 |
NLA |
| 2 |
21A1486 |
Stub axle R/H |
1 |
CWE |
| 2 |
21A1490 |
Stub axle L/H |
1 |
NLA |
| 3 |
2A7352 |
Stub axle circlip |
2 |
|
| 4 |
LBS507 |
Bush for pivot arm |
2 |
CWE |
| 5 |
21A1375 |
Bracket on radius arm for hose |
2 |
NLA |
| 6 |
ACA9099 |
Radius arm pin |
2 |
|
| 7 |
ATJ4098 |
Roller bearing inner, was 13H442 |
2 |
|
| 8 |
2A7325 |
Bronze bush outer |
2 |
|
| 9 |
21A396 |
Metal grease sleeve, replaced by plastic sleeve |
2 |
|
| 10 |
2A7324 |
Outer thrust washer |
2 |
|
| 11 |
ACA9302 |
Inner thrust washer |
2 |
|
| 12 |
2A7327 |
Sealing rubber ring |
4 |
|
| 13 |
LWZ208 |
Spring washer |
4 |
|
| 14 |
FNZ508 |
Nut |
4 |
|
| 15 |
UHN400 |
Grease nipple |
2 |
|
| 16 |
GSV1125 |
Radius arm repair kit, was 8G7134 |
2 |
|
| 17 |
21A2023 |
Hub with studs |
1 |
|
| 17 |
21A1277 |
Hub with long studs, 1275GT 'S' |
1 |
|
| 18 |
21A2064 |
Wheel stud shaft length 1.375" 35mm |
1 |
Thread length 0.875" |
| 18 |
21A2064L |
Wheel stud shaft length 2.000" 50.80mm |
1 |
Thread length 1.125" |
| 18 |
ATA7085 |
Wheel stud shaft length 1.687" 42.65mm |
1 |
Thread length 1.000" |
| 18 |
21A1278 |
'S' Wheel stud shaft length 2.375" 60.30mm |
1 |
Thread length 0.750" |
| 18 |
ENJO-1039 |
Wheel stud shaft length 2.375" 60.30mm |
1 |
Thread length 1.125" |
| 18 |
ERA1268 |
Wheel stud shaft length 2.437" 62mm |
1 |
Thread length 1.000" |
| 19 |
88G322 |
Wheel nuts, round radius chamfer angle |
8 |
|
| 20 |
CN1 |
Chrome wheel nut |
16 |
Alternative to 88G322 |
| 20 |
CN4 |
Chrome wheel nut, wide base |
16 |
Alternative to 88G322 |
| 20 |
AHA8785 |
Chrome wheel nut, 60° chamfer dome - 1275GT Rostyle |
16 |
Weller steel, use CN2 |
| 20 |
CN2 |
Chrome wheel nut, 60° chamfer angle |
16 |
Weller steel and Rostyle |
| 20 |
CN5 |
Chrome wheel nut, wide base |
16 |
Alternative to CN2 |
| 21 |
GHS134 |
Metal backed 'S' rear hub oil seal |
2 |
Use GHS102 |
| 21 |
GHS102 |
Rear hub oil seal |
2 |
|
| 22 |
GHB116 |
Bearing without built in spacer |
4 |
NLA use GHK1352 |
| 22 |
GHB212 |
Bearing with built in spacer |
4 |
Part of GHK1352 |
| 23 |
2A7354 |
Spacer when GHB116 fitted |
2 |
|
| 24 |
GHK1352 |
Bearing kit with built in spacer and seals |
2 |
was GHK1008 |
| 24 |
GHB1548 |
Timken tapered roller bearing set with seals |
2 |
|
| 25 |
BTA672 |
Hub washer, was 21A1892 |
2 |
|
| 26 |
NL610041 |
Hub nut R/H |
1 |
|
| 26 |
FNN2410 |
Hub nut L/H |
1 |
Left hand thread- |
| 27 |
ATB4098 |
Grease retaining cap |
2 |
|
| 28 |
21A1507 |
Hand brake quadrant |
2 |
|
| 29 |
2K2545 |
Spring washer |
2 |
|
| 30 |
21A1512 |
Thrust washer |
2 |
|
| 31 |
21A1513 |
Spire clip |
2 |
|
